Catalogue

Safety Footwear

Steel and composite toe safety shoes, rigger boots, gum boots, shoe covers and welding leg guards.

Safety footwear for construction sites, workshops and wet work: low-cut and high-cut safety shoes, rigger boots, construction gum boots with or without a steel toe cap, and the disposable shoe covers and leather welding leg guards that go with them.

Where a model is certified, its EN ISO 20345 class is stated on its page and in the table below: S1 SRC, S1P SRC and S3 SRC under the 2011 edition of the standard, and S3L SR FO on the N321 under the current one. Toe caps are steel, composite or fiberglass, depending on the model.

10 products

Compare the range

Figures are from each product's datasheet. A dash means the datasheet does not state it.

ProductEN ISO 20345 classToe capProtective midsoleSizes
Construction Gum Boots Without steel toeNot statedNot statedNot statedEUR 39 - 46 + Height: 368 - 380 MM
Construction Gum Boots With steel toeNot statedNot statedNoneEUR 39 - 46 + Height: 368 - 380 MM
Low Cut Safety Shoes KPU upperEN ISO 20345:2011 S1 SRCCompositeNoneEUR 36-47
Low Cut Safety Shoes Suede leather upperEN ISO 20345:2011 S1 SRCSteelNoneEUR 36-47
Rigger BootsNot statedNot statedNot statedEUR 36-48
High Cut Safety ShoesEN ISO 20345:2011 S3 SRCSteelSteel plateEUR 36-48
Disposable Shoe CoverNot statedNot statedNot stated15x40 cm + Color: Blue
Safety Shoe N321S3L SR FOFiberglassPuncture resistantNot stated
Safety Shoes S1P SRCEN ISO 20345:2011 S1P SRCSteelNot statedEUR 39-45

Reading an EN ISO 20345 marking

Certified safety shoes in this range carry a class code from EN ISO 20345, the European standard widely used across the Gulf. The letters build on each other, so one code tells you what a shoe has been tested for.

SB
Basic safety footwear. The toe cap is tested against a 200 joule impact and a 15 kN compression load.
S1
SB, plus a closed heel area, antistatic properties and energy absorption in the heel.
S2
S1, plus an upper that resists water penetration and absorption.
S3
S2, plus a penetration-resistant midsole and a cleated outsole.
P
A penetration-resistant midsole, added to a class that does not already include one. S1P is an S1 shoe with this midsole.
L or S
Under the 2022 edition, which nail test a non-metal penetration-resistant midsole passed: L with a 4.5 mm nail, S with a 3.0 mm nail.
SRA, SRB, SRC
Slip resistance under the 2011 edition: SRA on ceramic tile with detergent, SRB on steel with glycerol, SRC on both.
SR
Slip resistance under the 2022 edition: the additional test on ceramic tile with glycerol, on top of the basic slip test every shoe must now pass.
FO
An outsole resistant to fuel oil.

Source: EN ISO 20345:2011 and EN ISO 20345:2022, Personal protective equipment — Safety footwear.

Questions

What does S1P mean on safety shoes?

S1P is an S1 safety shoe with a penetration-resistant midsole added. It has a tested toe cap, a closed heel, antistatic properties and an energy-absorbing heel, and the midsole stops a sharp object such as a nail passing through the sole. S1P does not include water resistance; that comes with S2 and S3.

What does SRC mean on safety shoes?

SRC is the slip-resistance marking from the 2011 edition of EN ISO 20345. It means the sole passed both slip tests: on ceramic tile with a detergent solution and on steel with glycerol. The 2022 edition replaced SRA, SRB and SRC with a basic slip test for every shoe and an additional SR marking.

What is the difference between S1P and S3 safety shoes?

Both have a tested toe cap and a penetration-resistant midsole. S3 adds an upper that resists water and a cleated outsole for grip on loose ground, which is why S3 is the usual choice for outdoor and wet sites and S1P for dry floors indoors.

Which Spartan safety shoes have a steel toe cap?

Low Cut Safety Shoes Suede leather upper, High Cut Safety Shoes and Safety Shoes S1P SRC have a steel toe cap, and Low Cut Safety Shoes KPU upper and Safety Shoe N321 have a non-metal toe cap. Steel and non-metal toe caps meet the same impact test under EN ISO 20345; non-metal caps are lighter and do not conduct heat or cold.

Can you supply safety shoes in bulk?

Yes. Spartan supplies safety footwear in bulk to buyers in Bahrain, the United Arab Emirates and Saudi Arabia. Add the products you need to an enquiry with quantities and your delivery location, and our team will reply within 3 working days with availability and pricing.